iE 250 Application SW (Flexible application)

2.0.10.1

25/06/2025

2.0.10.1 based on 2.0.9.0

New features

• The user can now read the device serial number in CODESYS

Corrections

• Opening I/Os in a backup or config file no longer results in an error popup
• Fixed issue with fieldbus connection handling that prevented correct connections from being displayed

2.0.9.0

04/05/2025

2.0.9.0 based on 2.0.8.1

New features

• Three pump logic routines can now be set up to control the pumping of a substance.
• Implement ECU diagnostic to enable run coil and ECU power while the engine is stopped.
• All configuration dependent values are now possible to use in the flexible Modbus. 

Changes

• Modbus timeout increased from 10 sec to 100 sec on iE 250 and iE 350. 
• Number of possible Modbus connections changed from 20 to 100 on iE 250 and iE 350.
• EIC: Volvo Penta EMS2.4: "Engine Override Control Mode" changed to "Speed control".  
• EIC: Volvo Penta EMS2.4: TSC1 will not be transmitted if VP70 is used for regulation. 
• Added write permission for "Priorities" when the controller is in emulation.

Corrections

• Fixed issue where changes made in the UI were not registered.
• Fixed issue where the "IO configuration" menu would show empty slots.
• Fixed issue where tree-structure menu groups could not be collapsed using touch.
• Fixed issue where iE 250 failed to start up without MIO module.
• Fixed issue where configuring a Modbus value to "true" made the value "255" instead of "1".
• Fixed issue where measurements from multiple ECUs were not shown in UI for e.g. configuring alarms.
• Fixed issue where display user could not clear DM2 logs.
• Fix issue where iE controller could not start without MIO module. 
• Fixed issue with missing alarm icons.
• Fixed issue where user could enter parameter values outside of valid range.
• Fixed checksum and counter for VP70.
• Fixed issue where PIM2.1 DIO levels were inverted.
• Fixed issue where removing network cable would activate system NOK, IO service error and "temperature too high" alarms.  
• Fixed issue where CODESYS user management files were not included in backup/restore.
• Fixed issue where linked outputs in CODESYS were hidden in the IO configuration.
• Fixed issue where PWM was not working on MIO2.1.
• Fixed issue where Genset was not deloading correctly when it was connected to mains.
• Fixed issue where BUS TIE breaker could not deload and open a ring connected busbar.

2.0.8.1

10/02/2025

Corrections

• Fixed issue that sometimes prevents start-up of controller.

Changes

• Improved wire break detection handling.

2.0.8.0

17/01/2025

2.0.8.0 based on 2.0.6.0

New features

• Web Config Tool: Added a Version page with version information of the different software components.
• Web Config Tool: Added support for PTP time synchronisation.
• It is now possible to manually disable/enable the USB port  when not in use. (cyber security).
• EIC: Added Cummins Industrial protocol.
• EIC: Added Baudouin 6M33 protocol.
• Added support for DIO2.1 and AIO2.1 plug-in modules.
• Added device descriptions for 600-series hardware modules for use in CODESYS.
• Added alarm to indicate unknown traffic on the DEIF network (cyber security).
• Network port configuration:  New "Standalone" mode to allow CODESYS to be used on Port 0.
• Added CustomLogic signals to display designer for extra monitoring capabilities.
• Added iE 7 Display support via Display Port for the iE 250 Base-mounted variant and the iE 350.

Changes

• Improvements to the IP address settings.
• Logs: Is is now possible to press Info when the search filter is highlighted.
• Introduced an alarm to inform users about malfunctioning hardware modules.
• Introduced an alarm to inform users about configuration issues on hardware modules.
• Added fuel level as an engine measurement.
• Increased the persistent storage to 128KB.
• Upgraded CODESYS runtime version to v3.5.20.40 
• J1939: Added 40 measurements to analogue output functions.
• Under frequency detection for NEL can now be specified to a tenth of a percentage point.

Corrections

• Fixed an issue causing DM2 logs to be empty.
• Fixed an issue causing display texts not to be translated.
• Fixed an issue that allowed users to change parameters without logging in.
• Fixed an issue where custom I/O tests were not shown.
• Fixed an issue where the DEF level gauge was shown on the dashboard for a Yanmar Stage V engine.
• Web Config Tool: Fixed an issue causing the user management to stay in edit mode.
• Web Config Tool: Fixed an issue preventing to write the time settings from the web interface.
• Fixed issues in user management preventing users from being deleted or having reassigned roles.
• Fixed an issue causing the status LED to go out of sync.
• Fixed MIO2.1 device description.
• Fixed issues with voltage measurement when emulating a split-phase system.
• Fixed an issue where "System no OK" alarm could occur after changing the time on the controller.
• Fixed an issue with phase-neutral voltage protections for split- and single-phase AC setups.
• Fixed an issue in DVC voltage parameters for split-phase.
• EIC: Fixed an issue causing Stage V lamps for Scania S8 (DEF warning lamp) and Isuzu (Regen warning lamp) not to work.