Multi-line 2 EC-1/GC-1 Application Software Std. Lang. Package series 1.x.

1.43.4

08/10/2010

This software applies to the following DEIF products:

• Multi-line 2 - EC-1/GC-1

Changes:

• Status of cable supervision in USW optimised

1.43.3

18/08/2009

• Wire break symbol in Chinese added.

1.43.2

18/06/2008

• Binary inputs with cable supervision updated.

1.43.1

04/02/2008

• Energy counter updated.

1.43.0

15/01/2008

• Multi input wirebreak failclass changed to warning

1.42.3

02/11/2007

• Multiinput wirebreak alarm updated.

1.42.2

22/06/2007

• SW version number corrected.

1.42.1

19/06/2007

• Extended stop updated when using frequency as running feedback.
• Remote puls start updated during cooldown

1.42.0

14/05/2007

New features:

• New digital input function, remote puls start
• New digital input function, remote puls stop
• New relay output function, auto mode indication

Changes:

• Mode (Auto/Local) is not stored, if power is removed from the controller.

1.41.2

28/02/2007

• Busbar transformer setting updated.

1.41.1

19/02/2007

Changes:

• Engine running relay now reacts to running feedback.
• Ext stop is now performed when running feedback is lost.
• Failclass error corrected in Hz / V failure alarm

1.41.0

03/01/2007

Changes:

• Shutdown possibility during start sequence added
• 4-20 mA input range improved.

1.40.4

01/10/2006

Changes:

• MB open / close feedback updated

1.40.3

22/08/2006

Changes:

• Chinese texts updated.
• Icons updated.
• CanOpen remote start/stop updated.
• Firepump updated with CAN alarm.
• Alarm relay B updated.
• Low power readout for USW scaled.
• Oilpressure readout for USW scaled.
• PF calculation updated.

1.40.2

21/03/2006

Changes:

• L1-0 error message updated

1.40.1

08/03/2006

Changes:

• Running hour counter updated.
• MB handling upon power up changed

1.40.0

08/02/2006

New features:

• VDO 3 range increased to 2400 ohm.
• External heater function added.
• New stop coil function added - stop coil no start
• L1-N value error alarm added.
• Mains failure frequency detection ON/OFF function added.
• Additional view added.
• Parameter groups added.
• GC-1 frequency readings shown with 1 decimal.
• Power readings shown with 1 decimal if Pnom < 49kW.
• Diode compensation function added.
• Test input added for AMF.
• New digital input texts added.
• New text "Coolant pressure" added to analog input (4-20mA).
• External trip of MB added to AMF sequences.
• Extra password level added.
• GB breaker delay function added.
• Oilpressure feedback added.

Changes:

• Some parameter settings updated.

1.30.5

29/11/2005

New features:

• New AMF situations added.
• Run status alarm added.

Changes:

• Fuel pump function updated.
• Stop coil funciton updated.
• Input functions updated (Idle run, firepump).
• Alarm / limit relay functions updated.
• Default settings updated (Charger gen).
• Breaker interlock updated.
• Start enable updated.
• Parameter menu updated.
• Setting of voltage transformers updated.
• Language handling updated.
• AMF functions updated.
• VDO user definable inputs updated.
• Run enable updated.
• Block (shutdown) updated.
• HW change to VDO inputs supported.
• Device number for options in USW updated.

1.30.2

21/10/2005

Changes:

• Tacho feedback updated
• E counter updated

1.30.1

05/10/2005

Changes:

• Test function updated.

1.30.0

05/10/2005

New features:

• Italian and Chinese language supported.
• Option H1 (CANopen) added.
• 1 second delay added to starter and tacho feedback

Changes:

• Writing of outputs from USW corrected.
• Cool down timer updated remote mode.

1.21.0

12/09/2005

New features:

• German, Spanish and French language supported.

Changes:

• Nominal voltage is phase-phase
• D+ timer updated
• Firepump updated
• "f/U..." texts changed

1.20.1

12/09/2005

Changes:

• Test function updated

1.20.0

03/08/2005

New features:

• Support for 3-phase measurementboard (GC-1)
• Support for option B3 (GC-1 AMF)

1.10.2

04/07/2005

Changes:

• Configurable outputs updated