Multi-line 2 BGC Application Software series 1.x.

Multi-line 2 BGC Application Software series 1.x.

You have chosen to download our software.

Within a few seconds, you will receive an email containing a download link.

Having trouble using the software? Please contact support@deif.com. 

Best regards, 

DEIF A/S

The software is subject to copyright DEIF A/S
By following the above mentioned link and downloading the file you automatically accept DEIF A/S copyright and license agreement (EULA). The license agreement can be found on www.deif.com/software

1.10.3

Changes:

  • Update of self-check functionality

1.10.3

15/05/2015

Changes:

  • Update of self-check functionality

1.10.2

23/02/2007

Changes:

  • Menu for Voltage Trip (Phase-Phase or Phase-Neutral) removed.

1.10.1

21/02/2005

Changes:

  • Handling of MB in VDE0108 AUS mode updated.
  • Rampdown updated.
  • Returning from JUMP menu sets to main view.
  • Mode "Load take over" updated.
  • Digital input alarm handling updated.
  • Emergency stop default set to OFF.

1.10.0

07/02/2005

Changes:

  • Setting if WARNING fail class should autoreset or not added
  • Analogue input readings optimised for better precision
  • Alarm acknowledge updated for option VDE0108
  • Factory settings of var export/import changed
  • interface to USW regarding inputs optimised
  • Analogue input board (option M15) reading optimised
  • Test mode updated

1.05.0

05/01/2005

Changes:

  • When breaker position is unknown, breaker LED will be flashing red.
  • Now possible to open GB in Island SEMI when Loadshare not present and breaker alarms active.
  • Ramp down added to TEST mode.
  • GB opens immediately in MAN mode when activated.
  • RPM max. settings changed from 2000 to 4000. Overspeed alarms corrected according to this. Improved handling when using external power setpoint.
  • Password to changing password changed. Must use master password level to change master password. Must use OEM password level to change OEM password.
  • In VDE0108 alarm horn is now set off when first alarm of multiple alarms is acknowledged.
  • Display is updated when using binary input for alarm acknowledge

1.04.5

12/11/2004

Changes:

  • Governor and AVR offset function modified

1.04.4

19/10/2004

Changes:

  • Manual stop in AUTO mode is changed
  • Test mode handling changed
  • Handling of other languages than English is changed

1.04.2

01/09/2004

Changes:

  • Handling of mains breaker supervision when using contactor setting changed to avoid alarm when combined with zero-voltage coil trip of mains.

1.04.1

02/08/2004

Changes:

  • Gen-set will ramp up in TEST mode.
  • Underlined characters of extended ASCII-table added.

1.04.0

28/06/2004

Changes:

  • USW interface improved
  • Reset regulation functionality adjusted
  • Settings possibilities for Emergency stop-menu extended
  • Handling of GB and MB modified

1.03.1

09/03/2004

Changes:

  • Manufactor name for CAN-open option changed
  • Option H4 - minor chnnges
  • USW interface regarding GB and MB extended
  • Alarm inhibit functionality changed during stop-sequence
  • Short circuit protection functionality changed
  • Failclass 'Warning' functionality improved
  • Functionality of frequency and voltage acceptance detection changed
  • Check of language added to USW control
  • GSM option menu extended
  • Service timers functionality added to USW
  • Event log update functionality changed
  • GB feedback handling changed
  • Single running in Island-mode functionality changed
  • Running hour calculation improved

1.03.0

11/02/2004

New features:

  • Modeshift can now be controlled with digital input or menu 4440
  • Stop mode in menu 4900 added
  • Option for support of VDE0108 is added
  • GB position error can be deactivated (digital configurable input set to 'not used')
  • Kvarh (import / export) counter added
  • Sprinkler-mode functionality changed to include Short circuit 1,2
  • Start attempt counter added
  • New menu for number of sprinkler start attempt is added
  • 'Load take over'-mode added
  • Emergency power relay output added
  • Collective fault output added
  • 'Ready for operation' functionality added
  • Possibility for activation of Test mode with conf. digital input added
  • Possibility for 2 X option M13 or M14 added
  • SMS module updated with ID number in every message
  • SMS module updated with alarmbuffer, all alarms will now be sent
  • Modbus communication is optimised

Changes:

  • SMS module is stopped if no phone-numbers are used
  • CCM communication is optimised
  • W_L menu and functionality removed
  • Static charger menu and functionality removed
  • Voltage level for running detection changed
  • Timing changed, if modeshift is on and mains failure occur
  • 'Peak current' renamed for 'Short circuit'
  • H4 option shown in USW
  • If a mains fail occurs during TEST mode the AMF sequence will start
  • USW stop command optimised
  • Static sync improved function
  • Improved power factor calculation
  • Password handling optimised
  • Menu handling in regard to Option A1 A2 A3 optimised
  • Default setting for secondary value for current trafo's for Generator and busbar changed
  • Counter handling (hours, CB, MB operations) optimised
  • Deload is interrupted if remote start/stop is changed from start -> stop -> start
  • MB operations optimsed during change of configuration
  • Function of Relay 13 optimised
  • Menu handling in regard to loadshare PCB optimised
  • Menu handling for Option M13 optimised
  • Possibility for Test-mode in Island mode removed
  • Mains-failure detection improved
  • Start enables functionality improved
  • Log-functionality improved
  • Failclass handling in auto mode optimised

1.01.2

07/11/2003

Changes:

  • Security regarding write/erase operation in boot-sector is improved.

1.01.1

10/10/2003

Changes:

  • The 8 Start/stop menus are adjusted
  • Menu 4250, 'ID BAUD' -> 'TYPE' corrected

1.01.0

03/10/2003

New features:

  • Can-Open support enabled
  • 'JDEC' engine communication added

Changes:

  • Line 3 adjusted when 'mode button' is used
  • Eventlog secured when power up less than 3sec
  • Frequency measurement below 20Hz is disabled due to a problem under stopping the gen-set.  This could in rare cases generate a reset of the unit.
  • Timing in case of 'MB trip externt' adjusted

1.00.4

29/08/2003

Changes:

  • Changed max limit in menu 1290 1300 from 300% -> 350%
  • Changed text string for 2180 + 2190 (Deadband - > limit)
  • Removed PF control settings, not used

1.00.3

01/08/2003

New features:

  • Option H4 CCM Caterpiller

Changes:

  • SMS phonenumber-interface to USW adjusted
  • Peak-current measurement improved
  • dfdt and vector-jump function improved
  • Stop of gen-set if mains-fail is added
  • Energy counters added

1.00.2

01/07/2003

New features:

  • Possibility to configure input for Alarm Acknowledge added
  • Possibility to configure input for Alarm Inhibit added
  • Possibiblity for activating fuel-logic

Changes:

  • Close of MB in auto changed
  • Text changed: 'Sprinker' -> 'Fire pump'
  • Generator protection moved into Option C1
  • Display update sequence optimized
  • VDO-input for fuel-logic is optimized

1.00.0

30/06/2003

Initial release

Como sempre, recomendamos a instalação dos aprimoramentos oferecidos para que você possa desfrutar totalmente do seu produto DEIF.

Todos os softwares aprimorados podem ser baixados, à sua conveniência e de maneira gratuita pelo site www.deif.com sob a opção “Software” e, em seguida, “Software Download”.

Em caso de dúvidas ou se enfrentar problemas para encontrar o software relevante para o seu produto, fique à vontade para contatar a DEIF A/S pelo telefone + 45 96149614 ou no escritório local da DEIF. Como alternativa, você pode enviar um e-mail para support@deif.com. Estamos sempre prontos para ajudar!