Multi-line 2 BGC Application Software series 2.x.

Multi-line 2 BGC Application Software series 2.x.

You have chosen to download our software.

Within a few seconds, you will receive an email containing a download link.

Having trouble using the software? Please contact support@deif.com. 

Best regards, 

DEIF A/S

The software is subject to copyright DEIF A/S
By following the above mentioned link and downloading the file you automatically accept DEIF A/S copyright and license agreement (EULA). The license agreement can be found on www.deif.com/software

2.50.3

This software applies to the following DEIF products:

Multi-line 2 - BGC

Multi-line 2 - BGC-L

Changes:

  • 1- Update of self-check functionality

2.50.3

13/04/2015

This software applies to the following DEIF products:

Multi-line 2 - BGC

Multi-line 2 - BGC-L

Changes:

  • 1- Update of self-check functionality

2.50.2

14/03/2013

Changes:

  • Start attempt settings was ignored.Corrected.
  • Minimum load in AMF was ignored.Corrected.

2.50.1

30/10/2012

  • The breaker did not open in Semi auto AMF mode. Only L1 decides if the frequency has dropped 0.5 Hz. Corrected.
  • The ramp down speed setting was ignored in Island mode and just ramped down as fast as possible. Corrected.
  • The genset stopped deloading and opened the breaker if it was 0.5 Hz over nominal settings. Corrected.

2.50.0

12/08/2010

New features:

  • VDO 3 can be used as temperature AND a Fuel sensor.

Changes:

  • Prompt for password when leaving block mode. Password level set in parameter 4901.
  • Ramp function implemented in Peak Shave mode.
  • Stop conditions in peak shaving improved.
  • VDO 2 calculations for level switch corrected.
  • MTU ADEC CAN communication improved.

2.40.2

17/10/2008

Improvement:

  • Stop command for Volvo and Scania engine communication changed

2.40.1

15/08/2008

  • Translations function corrected and max. number of languages reduced from 11 to 9

2.40.0

29/07/2008

New features:

  • Support of communication whit MTU-ADEC

Changes:

  • Volvo Penta EMS2 and SCANIA speed control updated.

2.31.3

12/12/2007

  • H2 option protocol now supports Modbus function 05 and 06.

2.31.2

29/10/2007

  • Password max limit changed to 32000.
  • Volvo Penta EMS2 preheat function updated.
  • Fire pump cooldown timer function updated.
  • M15 Analoge input measurements improved.

2.31.1

04/09/2007

  • Improved ramp up handling.
  • Volvo Penta EMS2 comm. error alarm updated.

2.31.0

19/06/2007

New features:

  • Regulation of reactive power, trough H2/H3

Changes:

  • Improved Ramp up delay handling.
  • Horn relay updated.
  • Improvement of external comm. enable input

2.30.3

16/01/2007

Changes:

  • Improved vector jump calculation.
  • BGC-L Input list updated

2.30.2

23/10/2006

Changes:

  • Handling of nominal power below 100kW updated.

2.30.1

28/09/2006

Changes:

  • GB handling updated.
  • IO view in util. SW updated.

2.30.0

05/09/2006

New features:

  • BGC-L for selected markets added.

Changes:

  • Frequency measurements >70Hz updated

2.21.2

26/06/2006

Changes:

  • GB operations adjusted upon back-sync-error.
  • Handling of MB close-failure updated.

2.21.1

08/03/2006

Changes:

  • Selection of Scania EMS 2 from USW updated.

2.21.0

24/02/2006

New features:

  • Scania EMS2 support added.

Changes:

  • Limit relay function updated.
  • Maximum frequency readout handling updated.
  • Volvo Penta EMS2 frequency change updated.
  • Power up sequence updated.

2.20.0

13/01/2006

New features:

  • Parallel enable added for Mains protections.
  • Channel 4800 (GOV / AVR relay setting) removed. Old relay settings was: GOV up: Relay 6, GOV down:
  • Relay 7, AVR up: Relay 8, AVR down: Relay 9.
  • Channel 4801-4804 added for GOV / AVR relay setting.
  • Auto start/stop input enabled in AMF.
  • Virtual input: Semi start, Semi MB off, Black busbar enable updated.
  • MLogic updated and new settings added.
  • Various Mlogic input / output added.
  • H5 Volvo Penta EMS 2 added.
  • Test mode setting: Simple, Full and Parallel.
  • Engine control relays configurable from MLogic when using Volvo Penta EMS 2
  • Self acknowledge added in USW. Channel 4452 "Auto reset warning FC" is removed.
  • Compact breaker handling added.
  • Manual control of GOV / AVR added for SEMI, TEST and AUTO.
  • DI alarms 1960-1990 added.
  • Actual language present in USW parameterlist.
  • Earth fault alarm and handling added.
  • Command timers output added to MLogic.
  • Selectable number of languages supported.
  • Service and master password settings available in JUMP menu.

Changes:

  • Overload 1 timer updated.
  • Horn function updated.
  • Gen-bar LED handling updated.
  • Short time parallel updated.
  • Semi mode handling updated.
  • Functionality of channel 2050 updated.
  • AVR reg. failure handling updated.
  • Mains fail handling updated.
  • MDEC protocol updated.
  • Scania protocol updated.
  • Back sync OFF functionality updated.
  • MB alarm updated.
  • Running detection updated.

2.12.2

28/11/2005

Changes:

  • MLogic command outputs updated.

2.12.1

17/11/2005

Changes:

  • Short time parallel updated
  • MLogic "MB synchronizing" updated
  • Minor updates

2.12.0

21/10/2005

New features:

  • Short time parallel added
  • VDE0108 sync. type updated

Changes:

  • Running, MB, GB offset updated
  • Password handling updated
  • Fuel pump logic/alarms updated
  • Short circuit precision updated
  • Hysterisys added to running detection
  • "Reset analogue input" functionality updated
  • M15 scaling added
  • FC updated on DI

2.11.1

30/06/2005

Changes:

  • Extended stop executed if running detection is lost

2.11.0

22/06/2005

New features:

  • MB trip failclass can be set in mains/bus protections
  • EIC alarms can be set to RUN activation

Changes:

  • GB trip stop failclass handling updated
  • Handling of overlap updated
  • Handling of view 3 updated

2.10.0

New features:

  • Support for MKIII PCB
  • Firepump cool down timer added
  • Delta V operation mode added

Changes:

  • Idle mode updated

Como sempre, recomendamos a instalação dos aprimoramentos oferecidos para que você possa desfrutar totalmente do seu produto DEIF.

Todos os softwares aprimorados podem ser baixados, à sua conveniência e de maneira gratuita pelo site www.deif.com sob a opção “Software” e, em seguida, “Software Download”.

Em caso de dúvidas ou se enfrentar problemas para encontrar o software relevante para o seu produto, fique à vontade para contatar a DEIF A/S pelo telefone + 45 96149614 ou no escritório local da DEIF. Como alternativa, você pode enviar um e-mail para support@deif.com. Estamos sempre prontos para ajudar!